These answers rely on published guidance from the U.S. Environmental Protection Agency (EPA), the Utah Department of Environmental Quality (DEQ), the Utah County Health Department, the Utah Geological Survey (UGS), Utah Code Title 15A, and Alpha Energy Laboratories pre-mitigation data compiled by UtahRadon.org. They provide general homeowner education, not medical or legal advice.
The EPA recommends mitigating a home when indoor radon measures 4.0 pCi/L (picocuries per liter) or higher. Because no threshold of radon exposure is proven completely safe, the EPA also advises considering mitigation when readings fall between 2.0 and 4.0 pCi/L. The World Health Organization uses an even lower benchmark of 2.7 pCi/L. For context, the EPA reports the U.S. average indoor level at about 1.3 pCi/L and outdoor air at about 0.4 pCi/L.
Pre-mitigation test data from Alpha Energy Laboratories (2015 through August 2025, compiled by UtahRadon.org) shows a Lehi average of 4.4 pCi/L across 4,733 tests and a Utah County average of 4.7 pCi/L across 26,930 tests—both above the EPA's 4.0 pCi/L action threshold. Nearby Northern Utah County cities average even higher in the same dataset, including Saratoga Springs at 4.9 pCi/L, Eagle Mountain at 4.7 pCi/L, Highland at 5.9 pCi/L, Lindon at 6.0 pCi/L, and Alpine at 6.4 pCi/L. Utah County Health Department notes that roughly 1 in 3 Utah homes tests elevated.
The EPA Map of Radon Zones was published in 1993 using broad regional estimates and designated Utah County as Zone 2 (predicted average 2.0 to 4.0 pCi/L). The EPA explicitly states that the 1993 zone map must be supplemented with local test data and must never be used to decide whether to skip testing. Decades of newer laboratory results show Utah County's measured average is 4.7 pCi/L, proving why every individual home needs its own test.
Yes. Newer Silicon Slopes and lake-bench subdivisions are built with tighter building envelopes, insulated foundations, and mechanical ventilation patterns that can create negative indoor pressure, drawing soil gas up through control joints, utility penetrations, and sump pits. Even if your builder installed a passive PVC radon pipe under the slab, the EPA states every new home should be tested after occupancy because passive stacks typically reduce radon by 30% to 70% and may still leave readings above 4.0 pCi/L.
No. Under Utah Code Section 15A-3-206, Appendix F of the International Residential Code (Radon Control Methods) is omitted from mandatory statewide requirements. If a builder voluntarily installs passive radon controls or portions of them, Utah statute states the installation must conform to IRC Appendix F, and no extra municipal building inspection is required solely for that voluntary installation.
Homeowners have three straightforward options. First, you can order a discounted mail-in short-term test kit through Utah DEQ at Radon.Utah.gov (listed at $22.95 in the Utah County Health Department's November 2026 notice). Second, between October and March, Utah County residents can borrow a professional continuous radon monitor from the Utah County Health Department in Provo for $25 for a two-day test (plus a $1.50 card fee; not valid for real estate transactions). Third, you can hire an independent NRPP- or NRSB-certified measurement professional for a 48-hour continuous test—especially important during a home purchase or sale.
Published Utah public-agency estimates give a helpful baseline: the Utah Geological Survey reports that active mitigation systems in existing homes typically run $1,200 to $1,700, while Utah DEQ guidance cites roughly $1,500 to $2,000 for standard residential installs, and UGS notes radon-resistant features during new construction cost around $500. Actual pricing depends on foundation layout, finished basements, crawl space membranes, electrical access, and whether a passive rough-in pipe already reaches the attic. An independent contractor gives you a written quote after reviewing your home.
A certified mitigator core-drills a suction pit through the basement slab (or taps an existing sump or passive rough-in), connects sealed PVC vent piping routed up through a garage, closet, or exterior wall to an inline radon fan mounted in an attic or outside the living envelope, and vents soil gas above the roofline. The continuous negative pressure beneath the slab intercepts radon before it can enter the basement. EPA reports active sub-slab suction can reduce indoor radon by 50% to 99%.
A certified mitigator can inspect the existing stub-out, verify whether it connects to a sub-slab gravel bed and exits properly through the roof, add a properly sized radon fan in the attic or exterior, wire it to the attic junction box if present, install a U-tube manometer warning gauge, and run a follow-up test. Converting a functional rough-in avoids concrete coring inside finished basements.
Utah DEQ states that contractors installing radon mitigation systems must hold an active Utah Division of Professional Licensing (DOPL) contractor license under an approved classification—S354 (Radon Mitigation), B100 (General Building), R100 (Residential/Small Commercial), E200 (General Electrical), P200 (General Plumbing), or S350 (HVAC)—and notes that a handyman registration is not permitted. Utah DEQ also recommends verifying active NRPP or NRSB national radon certification.
We are not aware of any Utah or federal statute requiring a radon test or mitigation system as a legal condition of selling a home. However, Utah's standard seller property disclosure asks about known radon conditions, and buyers frequently request a 48-hour test during due diligence. Always consult your real estate agent or attorney for contract-specific advice.
The EPA recommends running a post-mitigation test within 30 days of installation, waiting at least 24 hours after the fan starts operating, and keeping the fan running continuously 24/7. Check the manometer pressure gauge regularly to verify vacuum draw, and retest the home at least every two years (or after major renovations or HVAC changes).